Osmo Polyx Original Floor Oil - 2.5L
Hazard informationNot classifiedsafety data sheet available on request (EUH210)
Hazard information
Not classified as hazardous under CLP Regulation (EC) No 1272/2008. No hazard pictogram or signal word applies. The label carries the following statements:
- EUH210 — Safety data sheet available on request.
Label warning: Wash out any used cloth impregnated with this product immediately after use or store it in an airtight container (danger of self-ignition).
Read the label and the Safety Data Sheet before use. The SDS is in the Datasheets section on this page. Hazard information taken from the manufacturer's Safety Data Sheet, revision 05.12.2024.
THE WHOLE-FLOOR SIZE
Polyx-Oil Original is the hardwax-oil most timber floors in Ireland end up finished with, and the reason is maintenance. It penetrates the wood and leaves a microporous wax film rather than a sealed lacquer skin, so it will not crack, peel, flake or blister. When a lacquered floor wears through at the doorways you sand the whole room back; when an oiled floor wears, you clean it and put one coat on the worn area.
It is high-solid and genuinely hardwearing, resistant to water, dirt, abrasion and to the spills that actually happen — wine, tea, cola, juice. Once cured it is saliva-resistant and sweatproof to EN 71-3, which is the standard for children's toys, so it is safe under cots and in playrooms.
What 2.5 litres covers
At 24 m² per litre per coat, a 2.5L tin gives 60 m² in one coat, or about 30 m² finished in the two coats a bare floor needs. That is a typical living room, two average bedrooms, or a hall, stairs and landing.
Buy the whole floor in one tin where you can. Sheen level is consistent between batches but the safest way to guarantee an even finish across a large area is to work from a single tin, and to keep a wet edge along the boards rather than stopping mid-room.
Before you order
- Sand to the right grit. Floors finish at P120–150 — going finer closes the grain and the oil cannot penetrate, which is the single most common cause of a patchy floor. Vacuum thoroughly; fill gaps with Osmo Wood Putty first.
- Apply it thin. Thin coats are not a suggestion — a generously applied hardwax-oil stays tacky for days and has to be cleaned back off.
- Plan for the cure, not just the dry. Walkable after 8–10 hours, but full hardness takes 2–3 weeks. Keep rugs off and put furniture back on felt pads during that window.
- Oil darkens timber permanently — a "wet look" that does not fade. On oak that is usually the point; on pale maple or ash it is a real change. Sample first with a 5ml tester.
- Not for oily and extractive-rich hardwoods — cedar, iroko, mahogany, teak, sapele, bamboo, acacia, ipe, merbau, ebony, wenge, sycamore, rosewood. Use Osmo Wood Wax Finish Extra Thin on those instead.
- Smoked oak: use 3011 Gloss or 3032 Satin. 3062 Matt can bloom white on it.
Keeping it right
Sweep or vacuum, then damp mop with diluted Osmo Wash and Care — never saturate the boards, and never use a general-purpose floor cleaner, which strips the wax. Refresh worn traffic lines with Osmo Maintenance Oil rather than recoating the whole room.
At a glance
- Finishes: 3062 Matt, 3032 Satin, 3011 Gloss.
- For: interior wooden floors, furniture and worktops. Not for exterior use.
- Coats: 2 on bare timber, 1 to refresh.
- Coverage: 24 m²/L per coat.
- Drying: 8–10 hours between coats. Fully cured in 2–3 weeks.
- Apply with: flat brush, floor brush, hand pad or microfibre roller.
- Sanding: floors to P120–150, furniture to P180–240. Max 18% moisture content.
- Safe for children's toys once cured (EN 71-3), saliva-resistant and sweatproof.
- Sizes available: 5ml tester, 750ml, 2.5L.
Supporting Documentation
Full surface preparation, application detail, timber suitability and safety information:
Also available as a 5ml tester sachet for checking sheen, and in a 750ml tin for furniture and worktops.
Ireland & Northern Ireland — 1–3 working days. Charged by total order weight, VAT included:
- Up to 30 kg — €6.99, or free on orders over €85
- 30–60 kg — €13.99
- 60–100 kg — €27.99
- Over 100 kg — pallet delivery €49.99
Great Britain — 2–4 working days. €13.95 up to 30 kg, then €27.90, €55.90 and €99.90 by the same weight steps. There is no free delivery to Great Britain.
Rest of Europe — non-liquid items only, from €11.75, priced by destination and weight at checkout. Paint and other liquids ship to Ireland, Northern Ireland and Great Britain only.
Dispatch and collection — order before 12pm Monday to Friday and it ships the same day. Click & collect at Ballymount, Dublin 12 is free and often ready within the hour.
Returns — 14 days to change your mind and 14 more to send it back. Tinted paint is non-returnable once mixed.
