-15%

Osmo UV-Protection Oil Extra Clear Satin 2.5L

Osmo
€86.95 €73.91 ex. vat €90.91 inc. vat
CLEAR PROTECTION FOR VERTICAL STRUCTURES Highly water and dirt resistant Clear UV Protection Oil 410 is safe for humans, plants and animals when dry Clear UV Protection Oil 420 Extra is furnished with active ingredients to protect the coating against mould, algae and fungal attack. Microporous, penetrating finish which does not crack, peel or flake No sanding necessary when topping up coating Delays natural greying 12 x better than bare wood Colour intensifies bare wood ( wetted look)SURFACE PREPARATION Wood surface must be clean, dry and frost-free (moisture content max. 20%). Ideally, surfaces are sanded no finer than a P120 grit grade of sand paper. Sanding to finer grades will reduce required absorbency. Osmo UV-Protection-Oil Exra is ready to use. Do not thin. Stir well using a flat stirring stick or spatula before use. If possible, and if the wood is an absorbent species, please apply the first coat to all sides before installation. Fresh wood containing natural wood ingredients /extractives (eg: Cedar, Larch, Teak, Mahogany or Iroko) are often less absorbent and need to weather off first before applying the product. Please refer to website ‘Suitability’ section for more details. Weathering helps ingredient rich wood become more absorbent and the wood finish adheres optimally. Weathering is also required if ingredient rich wood has been freshly sanded or renovated. A coloured base coat is recommended, e.g. Natural Oil Woodstain. Coloured base coats can improve UV protection. For renovations, clean old microporous wood finishes thoroughly. De-grey any weathered bare wood with Osmo Wood Reviver Power-Gel before applying an Osmo exterior product. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works. To maintain absorbency, avoid sanding surfaces finer than a P120 grit. Weather ingredient rich wood after sanding. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces. Soft wood species like Pine or Spruce are more prone to blue stain, rot and insects. If desired, pre-treat these soft woods if possible on all sides with Osmo WR Base Coat. METHOD OF APPLICATION With Osmo Flat Brush or Osmo Microfibre Roller, apply thinly along the wood grain and spread well. Allow to dry for approx. 12 hours. Cooler temperatures, higher humidity levels or over application will delay drying. Once dry, apply the second coat thinly. When recoating colour treated surfaces, or for renovation works, one coat applied to the clean and dry surface is usually sufficient. NOTE Oils enhance and intensify the natural tone of wood (permanent wet effect). Depending on the degree of weathering, apply one coat of Osmo UV-Protection-Oil Extra to the cleaned and intact finish after approx. 3-4 years. Osmo UV-Protection-Oil is best suited to vertical structures whereby there is plenty of water run-off. For areas exposed to strong weathering, such as flat horizontals, weatherboard, post caps or window sills, please expect significantly shorter renovation intervals. Vertical elements mounted onto horizontal wood should have at least a 15 degree angle. Sharp edges must be rounded (radius > 2 mm). If the greying process has already begun, de-grey the surface with Osmo Wood Reviver Power Gel and refinish the dried surface with 2 thin coats of Osmo UV-Protection-Oil Extra. To achieve the UV protection factor 12, it is necessary to apply 2 thin coats of UV-Protection-Oil Extra. With only one coat on untreated wood, the life of the coating is significantly shorter. Using power washers will severely decrease the coverage of the finish and general or multi-purpose cleaners will increase the frequency of maintenance and recoating. CARE Regular Cleaning: Damp cleaning with Osmo Spray-Cleaner or diluted Osmo Decking Cleaner . Occasional Maintenance: If necessary, intensive cleaning and refreshing using Osmo Wood Reviver Power Gel or Osmo Gard Clean. Recoating: Simply re-apply one thin coat onto the clean and dry surface when signs of wear become visible.

Customer Reviews

Based on 1 review Write a review
The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.
Osmo UV-Protection Oil Extra Clear Satin 2.5L
You have successfully subscribed!
This email has been registered
Newsletter

Net Orders Checkout

Item Price Qty Total
Subtotal €0.00
Shipping
Total

Shipping Address

Shipping Methods

Welcome to Shopify Store

I act like:

Select Country: