Renner Premium YO-10-C762 WB Polyurethane Furniture Topcoat
Hazard informationNot classifiedcontains a sensitiser (EUH208), safety data sheet available on request (EUH210) · both bases
Hazard information
Two bases in this listing. The hazard information for each is given below.
SBN base (white)
Not classified as hazardous under CLP Regulation (EC) No 1272/2008. No hazard pictogram or signal word applies. The label carries the following statements:
- EUH208: Contains 2,4,7,9-tetramethyldec-5-yne-4,7-diol and reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction.
- EUH210: Safety data sheet available on request.
NTR base (clear)
Not classified as hazardous under CLP Regulation (EC) No 1272/2008. No hazard pictogram or signal word applies. The label carries the following statements:
- EUH208: Contains 2-methyl-2H-isothiazol-3-one and reaction mass of 5-chloro-2-methyl-2H-isothiazol-3-one and 2-methyl-2H-isothiazol-3-one (3:1). May produce an allergic reaction.
- EUH210: Safety data sheet available on request.
Read the label and the Safety Data Sheet before use. The SDS for each base is in the Datasheets section on this page. Hazard information taken from the manufacturer's Safety Data Sheets, SBN base revision 07.08.2019; NTR base revision 11.09.2020.
Renner 10C762 WB Polyurethane Furniture Topcoat
Renner 10C762 WB Polyurethane Furniture Topcoat is a pigmented 1K water-based acrylic/polyurethane topcoat for interior use, built to pair with Renner's own primer system. It builds a hard, uniform matt finish.
Matched Primer and Crosslinker System for Renner 10C762
Bare or previously finished timber needs priming first. 10C762 is engineered to work with Renner's pigmented water-based primers, YL-M641 and YL-M643. Where a piece needs extra durability or chemical resistance, the topcoat can be cross-linked with 0.5 to 1% YC-M407, turning the same 1K product into a 2K finish without changing how it applies.
Fast Drying Times on Renner 10C762 Furniture Topcoat
At 20°C and 45 to 65% relative humidity, a 120 g/m² coat is dust-free in 45 minutes, ready to handle in 1.5 hours and stackable after 12 hours, which keeps a production run moving without long waits between stages.
Key Features & Benefits:
- Matched Primer Compatibility: pairs with YL-M641 and YL-M643
- Optional 2K Upgrade: cross-link with YC-M407 for extra durability
- Fast Dry Times: dust-free in 45 minutes, stackable in 12 hours
Perfect for:
- Furniture Makers & Joinery Workshops: flat parts, turned parts, chairs and picture frames
- Interior Trim & Fittings: skirting boards and general woodwork
- Spray Application Setups: conventional, air mix and airless equipment
Technical Specifications
- Base: water-based acrylic/polyurethane
- Recommended use: interior furniture, general purpose woodwork
- Available versions: clear (NTR, pigmentable up to 18%) and white (SBN)
- Solid content: 29% ±1 (Neutre), 37% ±1 (White)
- Specific weight: 1.040 ±0.030 g/cm³ (Neutre), 1.160 ±0.030 g/cm³ (White)
- Viscosity DIN 6: 30 ±5 seconds
- Spreading rate: 6 to 11 m² per litre
- Recommended application weight: 100 to 140 g/m²
- Shelf life: 12 months, stored between 5°C and 35°C
Applying Renner 10C762
Prime bare or previously coated timber with YL-M641 or YL-M643, and sand the substrate with 320 to 400 grit paper first. Apply at full strength rather than thinned with water, since maximum atomisation gives a better finish than dilution. Nozzle and pressure vary by equipment: a conventional spray gun runs a 2 to 2.5 mm nozzle at 3 to 4 bar, air mix uses an 11 nozzle at 80 to 110 bar, and airless runs the same 11 nozzle at 120 to 150 bar.
Mix the product thoroughly before use, keep application temperatures above 15°C, and clean tools with water straight after use or with AY M460 detergent once the film has dried. 10C762 is not recommended over nitrocellulose or polyurethane basecoats, only water-based, polyester or UV basecoats.
We can match virtually any colour from most major paint brands. Simply provide the brand name and colour name when placing your order. Our tinting system supports colours from Farrow & Ball, Little Greene, Colourtrend, and many more.
Deep, vibrant, and dark colours may require additional pigment, so a colourant surcharge may apply. We’ll always contact you to confirm any extra charge before tinting your paint.
Ireland & Northern Ireland — 1–3 working days. Charged by total order weight, VAT included:
- Up to 30 kg — €6.99, or free on orders over €85
- 30–60 kg — €13.99
- 60–100 kg — €27.99
- Over 100 kg — pallet delivery €49.99
Great Britain — 2–4 working days. €13.95 up to 30 kg, then €27.90, €55.90 and €99.90 by the same weight steps. There is no free delivery to Great Britain.
Rest of Europe — non-liquid items only, from €11.75, priced by destination and weight at checkout. Paint and other liquids ship to Ireland, Northern Ireland and Great Britain only.
Dispatch and collection — in-stock orders placed before 12pm Monday to Friday ship the same day. Click & collect at Ballymount, Dublin 12 is free and often ready within the hour.
Returns — 14 days to change your mind and 14 more to send it back. Tinted paint is non-returnable once mixed.
Frequently bought together
Trade price applied at checkout
