In-stock placed orders before 12pm ship the same day, Mon to Fri
Juno Pavimyc Clear Epoxy Primer 2/C - Clear
Ships Same DayIn-stock orders before 12pm
Free DeliveryOver €85 · Ireland & NI
Click & CollectBallymount, Dublin
✓ In Stock🚚 Ships same day if ordered before 12pm, Mon to Fri
Juno

Juno Pavimyc Clear Epoxy Primer 2/C - Clear



€280.00 inc. VAT
€227.64 exc. VAT
Free delivery on orders over €85 in Ireland & Northern Ireland · Same-day dispatch before 12pm, Mon to Fri
Quantity
1
This option combination is unavailable.
Hazard informationDangerFlame (GHS02), Corrosion (GHS05), Exclamation mark (GHS07), Health hazard (GHS08), Environment (GHS09) · two components

Hazard information

Two-component product. The hazard information for each component is given below.

Component A (base)

Signal word: Danger

Hazard pictograms: Flame (GHS02), Exclamation mark (GHS07), Health hazard (GHS08)

  • H226: Flammable liquid and vapour.
  • H304: May be fatal if swallowed and enters airways.
  • H312+H332: Harmful in contact with skin or if inhaled.
  • H315: Causes skin irritation.
  • H317: May cause an allergic skin reaction.
  • H319: Causes serious eye irritation.
  • H335: May cause respiratory irritation.
  • H336: May cause drowsiness or dizziness.
  • H373: May cause damage to organs through prolonged or repeated exposure (oral).
  • H412: Harmful to aquatic life with long lasting effects.

Contains: Epichlorohydrin/Bisphenol-A epoxy resin (700 < MW < 1100); Reaction mass of ethylbenzene and m-xylene and p-xylene; 1-methoxy-2-propanol; Xylene

Component B (hardener)

Signal word: Danger

Hazard pictograms: Flame (GHS02), Corrosion (GHS05), Exclamation mark (GHS07), Environment (GHS09)

  • H226: Flammable liquid and vapour.
  • H315: Causes skin irritation.
  • H317: May cause an allergic skin reaction.
  • H318: Causes serious eye damage.
  • H336: May cause drowsiness or dizziness.
  • H411: Toxic to aquatic life with long lasting effects.

Contains: Amines, polyethylenepoly-, triethylenetetramine fraction; 1-methoxy-2-propanol; Polyamide; propan-2-ol

Read the label and the Safety Data Sheet before use. The SDS is in the Datasheets section on this page. Hazard information taken from the manufacturer's Safety Data Sheet, component A revision 13.07.2022, component B revision 13.07.2022.

Bare concrete drinks epoxy. Roll a coating straight onto an untreated slab and you get dry patches, pinholes and a bond that lets go under traffic.

Juno Pavimyc Clear Epoxy Primer 2/C is the two-component epoxy primer that goes down first. It seals and consolidates the concrete and evens the absorption so the topcoat can key in, and it also primes non-porous floors such as tiles and stoneware. Clear, semi-gloss, 4L and 15L.

Coverage

Datasheet coverage is 12 m²/L at 25 microns dry film on a sound, evenly finished slab; a sanded, ground or porous floor takes more. Thin with Juno D-90 solvent to suit the porosity and order with headroom.

Getting the slab ready

Firm, dry and clean: no dust, grout, grease, loose material, efflorescence or mould. Sand or grind off laitance and curing agents, then vacuum. The open profile is what the primer keys into. Brush or roller, after a 1 m² test patch.

Mixing and working time

The ratio is 2 parts A to 1 part B, the same 2:1 by weight or volume. Measure a part kit, do not pour by eye. Stir A on its own, add B slowly under low-speed mechanical stirring, then stir for two minutes until perfectly homogenised. Leave it to stand: induction time is 30 minutes. Do not use the mix more than 8 hours after mixing.

Drying and overcoating

Touch dry in 6 to 8 hours. Overcoat within 24 hours at 20°C. The topcoat goes on inside the day.

Conditions it needs

  • Above 15°C: through application and the whole cure, so an unheated space needs heating overnight.
  • Relative humidity 70% maximum: routinely exceeded in an unheated building.
  • Substrate at least 3°C above dew point: take a slab reading, not an air reading.
  • Floor moisture 4% maximum: measured at 2 cm depth.
  • No upward moisture through the slab: a slab can read dry at 2 cm and still blister a sealed film.
  • New concrete completely set, minimum one month, and completely dry.

Where it does not go

Interior use only. Not a yard, a ramp or any slab open to the weather, and not on any surface containing bitumen. Do not apply with rain or strong wind in prospect. Solvent-based and flammable: ventilate and keep ignition sources away.

Ireland & Northern Ireland — 1–3 working days. Charged by total order weight, VAT included:

  • Up to 30 kg — €6.99, or free on orders over €85
  • 30–60 kg — €13.99
  • 60–100 kg — €27.99
  • Over 100 kg — pallet delivery €49.99

Great Britain — 2–4 working days. €13.95 up to 30 kg, then €27.90, €55.90 and €99.90 by the same weight steps. There is no free delivery to Great Britain.

Rest of Europe — non-liquid items only, from €11.75, priced by destination and weight at checkout. Paint and other liquids ship to Ireland, Northern Ireland and Great Britain only.

Dispatch and collection — in-stock orders placed before 12pm Monday to Friday ship the same day. Click & collect at Ballymount, Dublin 12 is free and often ready within the hour.

Returns — 14 days to change your mind and 14 more to send it back. Tinted paint is non-returnable once mixed.

Juno Pavimyc Clear Epoxy Primer 2/C - Clear
You have successfully subscribed!
This email has been registered
Newsletter

Welcome to Shopify Store

I act like:

Select Country: